10,5 KG / 52m² EP Epoxy Resin Laminate Casting Crystal Clear Gfk Floor 1A (Floor)

SKU: 6010

GTIN: 0737356359017

Category: DIPOXY-2K-700Floor

Available immediately

109,24 € 114,99 € 5%

10,40 € per 1 kg

incl. 19% VAT ,

Gewicht

Description
Reviews

- DIPOXY-crystal-clear-scratch-resistant-epoxy resin - 2K - DIPOXY-CCrystal-Clear-Scratch-Resistant-Epoxy-Resin - 2K -

- DIPOXY-2K-700Floor -

DIPOXY-2K-700Floor is a clear, low-viscosity epoxy resin (2 components) which is only available in Germany in
"Premium quality" is manufactured and sold!

For more scratch resistance and higher shear resistance, we also have the somewhat more expensive universal epoxy resin DIPOXY-2K-700 on offer!

DIPOXY-2K-700Floor Epoxy harz is ideal for floor coatings

and floor seals such as: factory floors, hall floors, parking garages, workshops, residential buildings,

Kitchen floors, bathroom floors, garage floors, sports halls, etc ...

The processing time always depends on the ambient temperature. But assume that it will not take longer than 60 minutes

will have. If you need more time, this is the best way to use it DIPOXY-2K-700PRO.

It costs more, but on average you have 3-6 times the processing time!

The solvent-free DIPOXY-2K-700Floor is used in a mixing ratio of 2: 1 (e.g. 100g A and 50g B)
Mass units (by weight) are mixed and can therefore be easily processed. Ideally, the
Components A and B mixed at a temperature of 10 ° C - 25 ° C. DIOPXY-2K-700 is basically
self-bleeding, for the best results, care should be taken to use approx. 250-350 rpm.
for about. Stir for 4-5 minutes until both components are well mixed and not so much air is worked into the epoxy resin mixture at the low speed!

Simply select the desired amount of epoxy resin and add it to the shopping cart. Then select the color pigments

and also put in the shopping cart

(We also have many other effect pigments in the shop or see below!)

The best results are obtained with ours developed for epoxy resins Pearl effect color pi

gment scored!

RAL colors are also possible (on demand)

! Caution, risk of burns!

As soon as both components are mixed, a chemical reaction occurs which releases heat
becomes. Depending on how high the mixture is in a glass or bucket, the heat may not be fast enough
can be discharged through the surface. So there is always the rule: "Better wide and flat than high
and narrow! "If, for example, a mixture of 300ml in a cup is approx. 15cm high will stand still
it probably (depending on the outside temperature) after 15-25 minutes. get so hot you burn yourself
can and then it hardens immediately! But if you put the same mixture in a bucket and put it
is only 1cm high, it doesn't get hot and you can probably work it well in 60 minutes!

You can also pour the finished material straight onto the floor (do not leave it in the bucket) so that the processing time is the longest

remains open (with non-absorbent floors)! The mass is easy to use with a water squeegee or a roller

Distribute telescopic rod!

If you need more time (3-5 times the time), it is best to use this DIPOXY-2K-700PRO!

Layer thickness approx. 2-3mm layer thickness approx.0.5mm (including primer)

Depending on what you want to do, the following information from our experiments will help you.

You can of course also use more material!

All information is provided without warranty!

Consumption quantities DIPOXY-2K-700 for floor coating (private and commercial):

The rough rule for consumption is:

1kg = 0.2mm height per 5m² (1m x 1m)

10kg therefore result in 50m²!

Optimal results and 3D effects can be achieved with a thicker layer, which also compensates for unevenness and small cracks in the floor!

To do this, proceed as follows:

1kg = 1mm height per 1m² (1m x 1m)

Primer with the same material (applied "normally" thick) (mostly black, white or transparent)

0.2-0.6 kg per m² (0.2-0.6 mm per m²)

Color effect layer (middle layer)

1 - 3 kg per m² (1 - 3 mm per m²)

Sealing (final layer is not absolutely necessary)

1 - 2kg per m² (1 - 2 mm per m²)

Consumption quantities Effect Pearl Pigment for floor coating (private and commercial):

Depending on how thin you want to apply, you need between 5g and 25g of the epoxy mass per kg of pigments.

DIPOXY-2K-700Floor is ideal for sealing parcel floors, plank floors and even on laminate

gives it a whole new look!

Very easy to use with a roller, spatula, brush or water squeegee!

Here we worked without shoes, so as not to leave any marks in the ground that is not yet fully solid!

Processing time / drip time:

at 10 ° C approx. 40-60min.
at 20 ° C approx. 20-40min.
at 30 ° C approx. 10-25min.
over 30 ° C is possible, but without a time limit!

Final strength:

at 10 ° C for at least 72 hours for walking and 10-14 days for heavy exercise.
at 20 ° C for at least 24 hours for walking and 6-10 days for heavy exercise.
at 30 ° C for at least 12 hours for walking and 2-5 days for heavy exercise.

Storage:

At least 1 year / ideally at 10-25 ° C, dry and protected from direct sunlight!

Hazard warnings:
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H317 can cause allergic reactions to your skin.
H411 ??Toxic to aquatic life with long lasting effects.


Safety instructions:
P261 Avoid breathing dust / smoke / gas / mist / vapor / aerosol.
Avoid the release of P273 into the environment.
P280 Wear protective gloves / eye protection / face protection.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes.
Remove any existing contact lenses if possible. Continue rinsing.
P321 Specific treatment (see on this label).
P501 Dispose of contents / container in accordance with local / regional / national /
international regulations.
EUH205 Contains epoxy constituents. Can cause allergic reactions.: · after skin contact: Wash off immediately with soap and water and rinse well.
· After eye contact: Eyes several minutes with opened eyelids under flowing
Rinse with water. Consult a doctor if symptoms persist.
· After ingestion: Do not induce vomiting, call for medical help immediately.
Rinse your mouth and drink plenty of water.

Further products from this family:

DIPOXY-2K-700PRO

was specially designed for thick film applications up to 10 centimeters, developed with a long open time! It can be used for example "River Table"

can be produced in one pour without any problems! The curing time is significantly longer than with our DIPOXY-2K-700 & 700Floor,

because we had to reduce the chemothermal reaction very much to get this To be able to achieve layer thickness!

We also have other items such as the universal one

DIPOXY-2K-700

for jewelry, table production, so-called "River Table", for

Floors, pond, aquarium and terrarium construction, as well as for boat, ship and aircraft construction. Also

Molded parts can be poured into silicone molds, for example, or carbon, aramid and

Fiber optic connections are used! Also ideally suited for model making!

PremiumPearl effect color pigments for best results!

If, contrary to expectations, you should have a problem or just want more information, just give us a call!

Our competent service staff will be happy to take care of your concerns and advise you professionally!

Where can I get an epoxy resin with this price / performance ratio?

Only with us!

Business hours:

Monday - Friday:

8:00 a.m. - 12:00 p.m. and 1:00 p.m. - 6:00 p.m.

Additional telephone information:

(limited)

Saturday & Sunday: 10:00 a.m. - 2:00 p.m.

Shipping weight:	11,25 kg
Content:	10,50 kg

There are no reviews yet.